Micro-Epsilon interface and signal-processing accessories Communication adapters
Micro-Epsilon interface and signal-processing accessories: accessories and system components by Micro-Epsilon for communication adapters.
Visit the Micro-Epsilon site (opens in a new tab)
Shared technical specifications for the series
Properties every model in the series has. What differs is in the models table below.
Range across models
The span covered by the models of the series together — not the range of each model.
| Operating temperature | 0–70 °C |
|---|---|
| Supply voltage | 5–36 V |
| Storage temperature | -20–80 °C |
| Output update rate | 100000–200000 Hz |
| Current consumption | 200–500 mA |
| ADC resolution | 14–16 bit |
| Baud rate | 9200–12000000 baud |
| Number of measurement channels | 1–4 |
Models in the series
One column per model: what differs between the models of the series.
| Parameter | DPU eli-m-ad51dd489ae5e6627bbd43d0 | IF1032/ETH eli-m-9f23885a1bd1bd049fa826c5 | IF2001/USB eli-m-35721df1c25134aa74715544 | IF2004/USB eli-m-4f8d6810bc5247a038ab8f8e | IF2008/ETH eli-m-b1ae07a985efec8c0d992a17 | IF2008/PCIE eli-m-ba473dc320aec09f27b9b795 | IF2035-EIP eli-m-6bc477e0074e9f357537ebb7 | IF2035-EtherCAT eli-m-4f0c3cc8987603de07eab245 | IF2035-PROFINET eli-m-28ba928f99d465e1027173dc | IF7001 eli-m-17d22baf6b6012b34c3a27ad |
|---|---|---|---|---|---|---|---|---|---|---|
| Operating temperature | 5–50 °C | 0–60 °C | Not specified | 5–50 °C | 0–50 °C | Not specified | 0–50 °C | 0–50 °C | 0–50 °C | 0–70 °C |
| interface_specification | RS422 / RS485 | Micro-Epsilon RS485 sensor protocol | Not specified | Not specified | Not specified | Unknown | Not specified | Not specified | Not specified | RS485 2-wire half-duplex |
| Supply voltage | 13–30 V | 5–36 V | Not specified | Not specified | 11–30 V | Not specified | 9–36 V | 9–36 V | 9–36 V | Not specified |
| Storage temperature | 0–50 °C | -10–75 °C | Not specified | 5–50 °C | 0–80 °C | Not specified | -20–70 °C | -20–70 °C | -20–70 °C | Not specified |
| Output update rate | 100000 Hz | Not specified | Not specified | Not specified | 200000 Hz | Not specified | Not specified | Not specified | Not specified | Not specified |
| Protection class (DIN EN 60529) | ip40 | ip40 | Not specified | ip40 | ip65 | Not specified | ip20 | ip20 | ip20 | ip20 |
| Current consumption | 200 mA | Not specified | Not specified | Not specified | Not specified | 500 mA | Not specified | Not specified | Not specified | Not specified |
| Interfaces | ethercat | ethercat | usb | usb | ethernet | Not specified | ethernet_ip | ethercat | profinet | usb |
| ADC resolution | 16 bit | 14 bit | Not specified | Not specified | Not specified | Not specified | Not specified | Not specified | Not specified | Not specified |
| Baud rate | Not specified | 9200–6250000 baud | 9600–12000000 baud | Not specified | Not specified | Not specified | 9600–4000000 baud | 9600–4000000 baud | 9600–4000000 baud | Not specified |
| Humidity | Not specified | 5–95 %RH | Not specified | 5–95 %RH | 5–95 %RH | Not specified | 5–95 %RH | 5–95 %RH | 5–95 %RH | 5–95 %RH |
| ADC sampling rate | Not specified | 4000 samples/s | Not specified | Not specified | Not specified | Not specified | Not specified | Not specified | Not specified | Not specified |
| תחום קצבי דגימת ADC | Not specified | 2–4000 samples/s | Not specified | Not specified | Not specified | Not specified | Not specified | Not specified | Not specified | Not specified |
| source_nominal_supply_voltage_v | Not specified | Not specified | Nominal value: 24 VDC | Not specified | Not specified | Not specified | Not specified | Not specified | Not specified | Not specified |
| source_host_side_data_interface | Not specified | Not specified | Data output via USB | Not specified | Not specified | Not specified | Not specified | Not specified | Not specified | Not specified |
| Number of measurement channels | Not specified | Not specified | 1 | 4 | Not specified | Not specified | Not specified | Not specified | Not specified | 1 |
| source_interface_module_configuration_notes | Not specified | Not specified | Passes through laser on/off, switch signals and function output; screw-terminal sensor connection; aluminum housing. | Not specified | Not specified | IF2008E expansion board: additional two digital controller signals, two analog controller signals, and eight I/O signals; expansion board is mentioned as a component, not a separate catalog identity. | Source matrix prints IF2035/ENETIP; catalog order-code uses EIP spelling. | EtherCAT is listed as a supported IF2035 protocol; source matrix does not print a distinct EtherCAT model-code row. | Source matrix prints IF2035/PNET; catalog order-code uses PROFINET spelling. | Not specified |
| Sensor input interface | Not specified | Not specified | rs422 | rs422 | rs422 | Not specified | rs485 | rs422 | rs485 | Not specified |
| Weight | Not specified | Not specified | Not specified | Not specified | 1.7 kg | Not specified | Not specified | Not specified | Not specified | Not specified |
| Digital inputs | Not specified | Not specified | Not specified | Not specified | 4 | Not specified | Not specified | Not specified | Not specified | Not specified |
| Network link rate | Not specified | Not specified | Not specified | Not specified | 100 Mbit/s | Not specified | Not specified | Not specified | Not specified | Not specified |
| Digital outputs | Not specified | Not specified | Not specified | Not specified | 4 | Not specified | Not specified | Not specified | Not specified | Not specified |
| Encoder channels | Not specified | Not specified | Not specified | Not specified | Not specified | 2 | Not specified | Not specified | Not specified | Not specified |
| source_digital_sensor_channel_count_with_expansion | Not specified | Not specified | Not specified | Not specified | Not specified | The IF2008E adds sensor connections 5 and 6; total six digital sensors | Not specified | Not specified | Not specified | Not specified |
| source_host_bus_interface | Not specified | Not specified | Not specified | Not specified | Not specified | PCI-Express x1 interface | Not specified | Not specified | Not specified | Not specified |
| source_digital_sensor_channel_count | Not specified | Not specified | Not specified | Not specified | Not specified | Sensor connections 1-4 on IF2008/PCIe basis board | Not specified | Not specified | Not specified | Not specified |
| source_sensor_digital_interface_frequency_limit_hz | Not specified | Not specified | Not specified | Not specified | Not specified | input/output frequency max. 5 MHz | Not specified | Not specified | Not specified | Not specified |
| source_encoder_supply_voltage_v | Not specified | Not specified | Not specified | Not specified | Not specified | Power supply of encoders with +5 V from PCI power supply | Not specified | Not specified | Not specified | Not specified |
| source_synchronous_digital_sensor_signals | Not specified | Not specified | Not specified | Not specified | Not specified | Four digital sensor signals | Not specified | Not specified | Not specified | Not specified |
| source_fifo_storage | Not specified | Not specified | Not specified | Not specified | Not specified | Data stored in FIFO memory for block processing | Not specified | Not specified | Not specified | Not specified |
| source_maximum_ambient_temperature_c | Not specified | Not specified | Not specified | Not specified | Not specified | +40 °C | Not specified | Not specified | Not specified | Not specified |
| Fieldbus protocol | Not specified | Not specified | Not specified | Not specified | Not specified | Not specified | ethernet_ip | ethercat | profinet | Not specified |
| source_network_connections | Not specified | Not specified | Not specified | Not specified | Not specified | Not specified | Two network connections | Two network connections | Two network connections | Not specified |
| source_oversampling_factor | Not specified | Not specified | Not specified | Not specified | Not specified | Not specified | Not specified | 4-fold oversampling enables faster measurements than bus cycle | Not specified | Not specified |
| Status | Active | Active | Active | Active | Active | Active | Active | Active | Active | Active |
| Datasheet | PDF — IF1032/ETH (opens in a new tab) | PDF — IF2035-EtherCAT (opens in a new tab) | PDF — IF2035-PROFINET (opens in a new tab) |
The industries we serve
-
-
Aerospace
- Aircraft door-lock position detection
- Airlines & Aerospace Our balancing machines and moment weighing scales for aerospace drives ensure maximum precision, ease of use, and modular flexibility delivering reliability and performance without compromise contributing to your economic success.
- Automatic balancing machines Automatic balancing machines from Schenck are advanced solutions for precise balancing of rotating components in automated production processes. We offer systems and stations for balancing crankshafts, wheels and tires, turbochargers, electric armatures, drives, axle drive units, torque converters, drive shafts, disc-shaped rotors, as well as fans. Our systems increase productivity, ensure consistent quality, and are tailored to the needs of the automotive, energy, and industrial sectors.
-
Medical industry
-
Environment
-
Electric motor manufacturing
-
Food industry
-
Automotive industry
- Airlines & Aerospace Our balancing machines and moment weighing scales for aerospace drives ensure maximum precision, ease of use, and modular flexibility delivering reliability and performance without compromise contributing to your economic success.
- Automatic balancing machines Automatic balancing machines from Schenck are advanced solutions for precise balancing of rotating components in automated production processes. We offer systems and stations for balancing crankshafts, wheels and tires, turbochargers, electric armatures, drives, axle drive units, torque converters, drive shafts, disc-shaped rotors, as well as fans. Our systems increase productivity, ensure consistent quality, and are tailored to the needs of the automotive, energy, and industrial sectors.
- Axle Drives With our balancing machines for front and rear axle transmissions, the measured unbalance is corrected by drilling into the drive flanges of the transmissions (welding optional). We support you with our interdisciplinary expertise in the production of front and rear axle transmissions from the initial idea to the design stage through to series production.
-
Industrial automation
-
Plastics
-
Optics
-
3D printing
-
Battery manufacturing
Frequently asked questions
Answers to the most common questions about our products and services
Specify sensor model, its output protocol and the required PC/PLC interface. Connector shape or RS422 alone does not establish compatibility.
When combining two sensor signals for calculations such as thickness or diameter. DPU provides synchronous acquisition and calculation programs for compatible models.
Interface conversion does not establish that. Assess conversion error, resolution and throughput alongside sensor specifications.
Match input count, supported sensor types and synchronization. IF2004/USB and IF2008/ETH, for example, provide different channel counts and PC interfaces.
DPU documents parallel data output through three interfaces. Select outputs and analog scaling for the control system; this capability does not automatically apply to every interface adapter.
Get a quote or advice
Tell us what you need and an engineer will come back to you.
Request a quote for this product